All CATAGORY
GALO 150-350kg swing gate motor
Offer price for sale， best price nice product
Swing Gate Opener Features & Options:
1. In case of power failure: Use the manual override key to release the clutch to
open or close the gate manually.
2. When Gate is Obstructed: Gate stops .
3. Optional: The Gate Opener Controller can be connected to a solar system, a
flash light warning, a photocell, back up battery, keypad and other access control
devices.
4. Speed Control: Gate opening and closing speed can be adjusted.
5. Gentle Start: The Gate Opener is equipped with a soft start function.
6. Auto Close: The Gate Opener System is equipped with Auto close function with adjustable closing time delay.
7. Single or Dual Gate: Either Single or Dual Swing Gate can be opened.
8. Multiple Remote Transmitters: The Controller can easily accommodate
several unique extra remotes to control the swing gate opener
9. Battery Back Up: DC 24V back up battery can be incorporated
10. Optional Devices: DC 24V Gate Lock ,photocell ,keypad , photocell,push
button,large size or small size control box.
11. The Gate Opener can be configured to allow smooth noiseless operation.
12. The Gate Opener can be configured to enable open condition as default, or
close condition as default depending on the placement of the provided hardware
bracket brackets.
Technical Specifications
Motor voltage: 24VDC 60W
Input power:AC/DC24V±10% / 220VAC±10% / 120VAC±10%
Rotational speed：300 RPM
Arm's extended speed：2.4 cm/s
Arm's max travel：300 mm
Continue running time: 5 minutes
Max single-leaf length： 2.5meters
Max single-leaf weight：300-400 KG
Environment Temperature：-20°C ~ +50°C
Protection Class：IP55
Max gate open angle: 110 degree
Dual Swing Gate Gross weight : 18kg
Packing list，complete set
2 x DC gate motor that are pre-wired with motor cables
2 x Override spanners
2 x Remote controls
1 x Control panel
2 x Post mounting bracket
2 x Gate mounting bracket
1 x Rubber Gate Stop
1 x Instruction manual
Press the selected picture package delivery
SWING GATE OPERATOR
1. 2 SIDE terminal is used for connecting any external device that operates doublegate
2. COM terminal is COMMON used for connecting the “ground” of external devices
3. 1 SIDE terminal is used for connecting any external device that operates single gate
4. Swipe Card terminal is used for connecting any external devices that will operate toopen the gate
5. COM terminal is COMMON used for connecting the “ground” of external devices
6. Infrared terminal is used for connecting photo electric sensor
7. 12V DC output is used for connecting photo electric sensor (Continuous outputcurrent <=200mA)
8. 24V battery output is used for connecting the back up battery +
9. 24V battery output is used for connecting the back up battery –
10. 24V DC output is used for connecting external device. (such as photo electricsensor, max current output 1A)
11. GND is used for connecting the “ground” of external devices
12. 24V DC lamp output is used for connecting flash light +.
13. 24V DC lamp output is used for connecting flash light -.
14. 24V DC lock output—the NF terminal which used for connecting the electric lock
15. COM is COMMON used for connecting the “ground” of lock
16. 24V DC lock output—the NA terminal which used for connecting the magneticlock
17. 24V DC alarm output
18. 24V DC alarm output
19. and 20. Motor1 terminal is used for connecting the motor 1 installed on the gatethat opens later and close first. This terminal connect 1st red wire (counted from yourleft hand side to right hand side)
21. and 22. Motor2 Delay terminal is used for connecting the motor 2 installed on thegate that opens first and close later. This terminal connect 1st blue wire (countedfrom your left hand side to right hand side). NOTE! If for single gate, the gate motorjust can connect the Motor2 Delay terminal.
23. AC24V input is used for connecting the transformer
24. AC24V input is used for connecting the transformer
25. digital display is used for showing you the setting data
26. INC+ is used for figure increase when setting the data
27. FUN is used for store the data
28. DEC- is used for figure decrease when setting the data
29. Learning button is used for program/remove remote
